Universele draaibank C0636A×750
HEGE SNELHEID BANKDRAAIBANK MASINE
1. Presyzje-slypferhurde bêdwegen
2. De spindel wurdt stipe troch winske presyzje-rollagers
3. Headstock-gears binne makke fan heechweardich stiel, gemalen en ferhurde
4. Ferwiderbere gat is foarsjoen foar wurk mei gruttere diameter
5. Maklike operaasje snelheidsferoaringshendels
6. Spindelsnelheidsberik 70 ~ 2000r / min
7. Twa bêden fan ferskillende lingten binne beskikber
8. Maklike operearjende fersnellingsbak hat ferskate feeds en triedsnijfunksje
9. D1-4 camlock spindelnoas
| MODELLEN | C0632A×750 | C0632A×1000 | C0636A×750 | C0636A×1000 |
| Swing oer bêd | 330 mm (13") | 360 mm (14") | 358 mm (14") | |
| Swing oer krúsglijbaan | 198 mm (7-25/32") | 224 mm (8-13/16") | 223 mm (8-25/32") | |
| Swing yn gatdiameter | 476 mm (18-3/4") | 502 mm (19-3/4") | 502 mm (19-3/4") | |
| Swing yn lingte | 210 mm (8-1/4") | 210 mm (8-1/4") | 210 mm (8-1/4") | |
| Sintrumhichte | 166 mm (6-1/2") | 179mm (7") | 179mm (7") | |
| Jout ta tusken | 750mm (30") | 1000mm (40") | 750mm (30") | 1000mm (40") |
| Breedte fan it bêd | 187 mm (7-3/8") | 187 mm (7-3/8") | 187 mm (7-3/8") | |
| Bêdlingte | 1405 mm (55-5/16") | 1655 mm (65-1/8") | 1405 mm (55-5/16") | 1655 mm (65-1/8") |
| Bêdhichte | 290 mm (11-13/32") | 290 mm (11-13/32") | 290 mm (11-13/32") | |
| Spindelboring | 38 mm (1-1/2") | 38 mm (1-1/2") | 38 mm (1-1/2") | |
| Spindelnoas | D1-4" | D1-4" | D1-4" | |
| Taper yn 'e noas | MT NR. 5 | MT NR. 5 | MT NR. 5 | |
| Taper yn 'e mouwe | MT NR. 3 | MT NR. 3 | MT NR. 3 | |
| Snelheden nûmer | 8 | 8 | 8 | |
| Berik fan spindelsnelheid | 70-2000 r/min | 70-2000 r/min | 20~450 of 135~3000r.pm | |
| Breedte fan 'e krússlide | 130 mm (5-3/32″) | 130 mm (5-3/32″) | 130 mm (5-3/32″) | |
| Dwarsslideferfier | 170 mm (6-11/16") | 170 mm (6-11/16") | 160 mm (6-5/16") | |
| Breedte fan gearstalde rêst | 80mm (3-1/8″) | 80mm (3-1/8″) | 80mm (3-1/8″) | |
| Gearstalde rêstreis | 95 mm (3-9/16") | 95 mm (3-9/16") | 95 mm (3-9/16") | |
| Diameter fan 'e leadskroef | 22mm (7/8″) | 22mm (7/8″) | 22mm (7/8″) | |
| Loodskroefdraad | 8T.PI of 3mm | 8T.PI of 3mm | 8T.PI of 3mm | |
| Diameter fan 'e feedstang | 19mm (3/4") | 19mm (3/4") | 19mm (3/4") | |
| Maksimum seksje fan snijgereedschap | 16mm × 16mm (5/8" × 5/8") | 16mm × 16mm (5/8" × 5/8") | 16mm × 16mm (5/8" × 5/8") | |
| Triedden keizerlike toanhichte | 34 nr. 4-56 TPI | 34 nr. 4-56 TPI | 34 nr. 4-56 TPI | |
| Triedden metryske toanhichte | 26 nûmers 0,4-7 MP | 26 nûmers 0,4-7 MP | 26 nûmers 0,4-7 MP | |
| Longitudinale feeds imperial | 32 nûmers 0.002-0.548"/Rev. | 32 nûmers 0.002-0.548"/Rev. | 32 nûmers 0.002-0.548"/Rev. | |
| Longitudinale feeds metrysk | 32 nûmers 0,052-0,392 mm/omw. | 32 nûmers 0,052-0,392 mm/omw. | 32 nûmers 0,052-0,392 mm/omw. | |
| Krúsfeeds imperial | 32 nr. 0.007-0.0187"/Rev) | 32 nr. 0.007-0.0187"/Rev. | 32 nr. 0.007-0.0187"/Rev. | |
| Krúsfeeds metriek | 32 nûmers 0,014-0,380 mm/omw. | 32 nûmers 0,014-0,380 mm/omw. | 32 nûmers 0,014-0,380 mm/omw. | |
| Diameter fan 'e veer | 32mm (1-1/4") | 32mm (1-1/4") | 32mm (1-1/4") | |
| Reizen mei in veer | 100mm (3-15/16") | 100mm (3-15/16") | 100mm (3-15/16") | |
| Quill taper | MT NR. 3 | MT NR. 3 | MT NR. 3 | |
| Foar haadmotor | 2HP, 3PH of 2PH, 1PH | 2HP, 3PH of 2PH, 1PH | 2HP, 3PH of 2PH, 1PH | |
